Nothing special, just use undocumented command sh and you are there (I found it out by a mistake):
danman@silverhorse:~$ nmap 10.0.0.138 Starting Nmap 7.60 ( https://nmap.org ) at 2018-03-26 22:54 CEST Nmap scan report for 10.0.0.138 Host is up (0.013s latency). Not shown: 996 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 23/tcp open telnet 80/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.14 seconds danman@silverhorse:~$ telnet 10.0.0.138 Trying 10.0.0.138... Connected to 10.0.0.138. Escape character is '^]'. ZyXEL VDSL Router Login: admin Password: admin > help ? help logout exit quit reboot adsl xdslctl xtm brctl cat loglevel logdest virtualserver ddns df dumpcfg dumpmdm meminfo psp kill dumpsysinfo dnsproxy syslog echo ifconfig ping ps pwd sntp snmp sysinfo tftp wlctl arp defaultgateway dhcpserver dhcpcondserv dns lan lanhosts passwd ppp restoredefault route save swversion uptime cfgupdate swupdate exitOnIdle wan rip igmp wlan telnetd natp sysstate sipalgctl celld autoexec fileShare igmp btt ledctl > sh shell Password: admin ~ # ls bin etc linuxrc proc tmp vmlinux.lz data firmware mnt sbin usr webs dev lib opt sys var
~ # cat /proc/cpuinfo system type : 963168VXB processor : 0 cpu model : Broadcom4350 V8.0 BogoMIPS : 398.33 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available unaligned exceptions : 1399 processor : 1 cpu model : Broadcom4350 V8.0 BogoMIPS : 402.43 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available unaligned exceptions : 1399 ~ # cat /proc/devices Character devices: 1 mem 2 pty 3 ttyp 4 ttyS 5 /dev/tty 5 /dev/console 5 /dev/ptmx 10 misc 90 mtd 108 ppp 128 ptm 136 pts 180 usb 189 usb_device 206 brcmboard 208 adsl 227 p8021ag 228 bcmxtmcfg 233 spu 238 bcmvlan 240 pwrmngt 241 bcmfap 242 fcache 243 ingqos 244 bpm 245 bcmarl 246 chipinfo 254 usb_endpoint Block devices: 259 blkext 8 sd 31 mtdblock 65 sd 66 sd 67 sd 68 sd 69 sd 70 sd 71 sd 128 sd 129 sd 130 sd 131 sd 132 sd 133 sd 134 sd 135 sd ~ # lsmod Module Size Used by Tainted: P nf_nat_tftp 1152 0 nf_nat_irc 1888 0 nf_nat_rtsp 4320 0 nf_nat_h323 6640 0 nf_nat_ftp 2608 0 nf_conntrack_tftp 4032 1 nf_nat_tftp nf_conntrack_irc 5264 1 nf_nat_irc nf_conntrack_rtsp 9872 1 nf_nat_rtsp nf_conntrack_ftp 7088 1 nf_nat_ftp nf_conntrack_h323 47520 1 nf_nat_h323 nf_nat_pptp 2416 0 nf_conntrack_pptp 5840 1 nf_nat_pptp nf_nat_proto_gre 1840 1 nf_nat_pptp nf_conntrack_proto_gre 5104 1 nf_conntrack_pptp nfnetlink_queue 8864 0 ipt_REJECT 2960 0 ipt_LOG 7520 13 ipt_REDIRECT 1504 0 ipt_MASQUERADE 4368 1 nfnetlink 4080 1 nfnetlink_queue xt_SKIPLOG 1200 0 xt_TCPMSS 4224 1 xt_limit 2112 17 xt_state 1728 32 nf_conntrack_ipv6 13568 15 xt_pkttype 1296 2 xt_recent 9728 6 iptable_nat 4896 1 nf_nat 16608 10 nf_nat_tftp,nf_nat_irc,nf_nat_rtsp,nf_nat_h323,nf_nat_ftp,nf_nat_pptp,nf_nat_proto_gre,ipt_REDIRECT,ipt_MASQUERADE,iptable_nat nf_conntrack_ipv4 13360 20 iptable_nat,nf_nat nf_defrag_ipv4 1536 1 nf_conntrack_ipv4 nf_conntrack 60848 19 nf_nat_tftp,nf_nat_irc,nf_nat_rtsp,nf_nat_h323,nf_nat_ftp,nf_conntrack_tftp,nf_conntrack_irc,nf_conntrack_rtsp,nf_conntrack_ftp,nf_conntrack_h323,nf_nat_pptp,nf_conntrack_pptp,nf_conntrack_proto_gre,ipt_MASQUERADE,xt_state,nf_conntrack_ipv6,iptable_nat,nf_nat,nf_conntrack_ipv4 ip6table_filter 2144 1 ip6table_mangle 2256 1 ip6_tables 13184 2 ip6table_filter,ip6table_mangle iptable_mangle 2304 1 iptable_filter 2240 1 ip_tables 12080 3 iptable_nat,iptable_mangle,iptable_filter xt_multiport 2720 0 xt_MARK 1888 25 xt_mark 1376 21 xt_length 1408 0 xt_mac 1264 0 xt_DSCP 2992 1 xt_dscp 2064 0 pwrmngtd 7216 0 bcmvlan 99472 0 wl 3450288 0 bcmarl 7440 0 bcm_usb 26512 0 bcm_enet 125584 2 pwrmngtd,wl adsldd 349600 0 bcmxtmcfg 78512 1 adsldd bcmfap 185120 1 bcmarl pktflow 112464 1 bcmfap bcm_bpm 208736 0 [permanent] bcm_ingqos 10560 0 chipinfo 1712 0 ~ # ifconfig bcmsw Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Base address:0xda00 br0 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 inet addr:10.0.0.138 Bcast:10.0.0.255 Mask:255.255.255.0 inet6 addr: fe80::1/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:477641 errors:2994 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:183 overruns:1293627 carrier:0 collisions:2473 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) br1 Link encap:Ethernet HWaddr B2:C8:2D:87:EA:13 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::b0c8:2dff:fe87:ea13/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:1556 carrier:0 collisions:26 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:105842 carrier:0 collisions:493 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth2 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth3 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth4 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:30 inet6 addr: fe80::1e74:dff:fe04:9f30/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:101428 carrier:0 collisions:443 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:19586 errors:91 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:19586 carrier:0 collisions:91 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ppp1.1 Link encap:Point-to-Point Protocol inet addr:85.135.150.207 P-t-P:84.16.59.41 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:859177 errors:1602 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:308035 carrier:0 collisions:1759 txqueuelen:3 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ptm0 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:34 inet6 addr: fe80::1e74:dff:fe04:9f34/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:902686 errors:1629 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:355872 carrier:0 collisions:1790 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ptm0.1 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:35 inet6 addr: fe80::1e74:dff:fe04:9f35/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:873364 errors:1629 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:355023 carrier:0 collisions:1787 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wl0 Link encap:Ethernet HWaddr 1C:74:0D:04:9F:33 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:503536 errors:2906 dropped:0 overruns:0 frame:0 TX packets:2247 errors:0 dropped:204 overruns:1352452 carrier:0 collisions:2704 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:15 Base address:0x4000 ~ # ~ # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination DOS_INPUT all -- 0.0.0.0/0 0.0.0.0/0 SERVICE_CONTROL all -- 0.0.0.0/0 0.0.0.0/0 FrwlInChk all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) target prot opt source destination DOS_FORWARD all -- 0.0.0.0/0 0.0.0.0/0 NAT_FORWARD all -- 0.0.0.0/0 0.0.0.0/0 DMZ_FORWARD all -- 0.0.0.0/0 0.0.0.0/0 FrwlForwardInChk all -- 0.0.0.0/0 0.0.0.0/0 FrwlForwardInChk all -- 0.0.0.0/0 0.0.0.0/0 FrwlForwardInChk all -- 0.0.0.0/0 0.0.0.0/0 FrwlForwardInChk all -- 0.0.0.0/0 0.0.0.0/0 FrwlForwardInChk all -- 0.0.0.0/0 0.0.0.0/0 FrwlForwardInChk all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination FrwlOutChk all -- 0.0.0.0/0 0.0.0.0/0 Chain DMZ_FORWARD (1 references) target prot opt source destination TCPMSS tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU Chain DOS_FORWARD (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 30/sec burst 10 SYN_FLOODING tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 PING_DEATH icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 state NEW Chain DOS_INPUT (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 30/sec burst 10 SYN_FLOODING tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 PORT_SCAN udp -- 0.0.0.0/0 0.0.0.0/0 state NEW PKTTYPE != broadcast recent: UPDATE seconds: 120 hit_count: 20 name: port_scan side: source all -- 0.0.0.0/0 0.0.0.0/0 recent: SET name: port_scan side: source PING_DEATH icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 state NEW Chain FrwlForwardInChk (6 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 FrwlOutChk all -- 0.0.0.0/0 0.0.0.0/0 FrwlOutChk all -- 0.0.0.0/0 0.0.0.0/0 Chain FrwlInChk (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:7547 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:7547 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:7547 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:7547 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:7547 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 limit: avg 6/hour burst 5 LOG flags 0 level 1 prefix `Intrusion -> ' DROP all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 Chain FrwlOutChk (3 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 Chain NAT_FORWARD (1 references) target prot opt source destination Chain PING_DEATH (2 references) target prot opt source destination RETURN icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 limit: avg 10/sec burst 10 LOG icmp -- 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 1 prefix `Ping of Death Attack:' DROP icmp -- 0.0.0.0/0 0.0.0.0/0 Chain PORT_SCAN (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 1/sec burst 4 LOG all -- 0.0.0.0/0 0.0.0.0/0 LOG flags 0 level 1 prefix `Port Scan Attack:' DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain SERVICE_CONTROL (1 references) target prot opt source destination ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 state ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:23 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:23 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:21 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:21 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:53 DROP udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:53 Chain SYN_FLOODING (2 references) target prot opt source destination RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 recent: UPDATE seconds: 60 hit_count: 1 name: SYN_FLOOD side: source tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 recent: SET name: SYN_FLOOD side: source LOG tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 LOG flags 0 level 1 prefix `SYN FLOODING Attack:' DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp flags:0x17/0x02 ~ # ~ # uname -a Linux (none) 2.6.30 #2 SMP PREEMPT Fri Jan 20 10:19:06 CST 2017 mips GNU/Linux ~ # mount rootfs on / type rootfs (rw) mtd:rootfs on / type jffs2 (ro,relatime) proc on /proc type proc (rw,relatime) tmpfs on /var type tmpfs (rw,relatime,size=420k) tmpfs on /mnt type tmpfs (rw,relatime,size=16k) sysfs on /sys type sysfs (rw,relatime) /dev/mtdblock1 on /data type jffs2 (rw,relatime) /dev/mtdblock3 on /firmware type jffs2 (rw,relatime) usbfs on /proc/bus/usb type usbfs (rw,relatime) ~ # df -h Filesystem Size Used Available Use% Mounted on mtd:rootfs 18.0M 18.0M 0 100% / /dev/mtdblock1 4.0M 460.0K 3.6M 11% /data /dev/mtdblock3 19.6M 844.0K 18.8M 4% /firmware ~ # dmesg Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 Broadcom DSL NAND controller (BrcmNand Controller) -->brcmnand_scan: CS=0, numchips=1, csi=0 mtd->oobsize=0, mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=14152300, chipSelect=0 brcmnand_read_id: CS0: dev_id=98f00015 After: NandSelect=40000001, nandConfig=14152300 Block size=00020000, erase shift=17 NAND Config: Reg=14152300, chipSize=64 MB, blockSize=128K, erase_shift=11 busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 BrcmNAND mfg 98 f0 TOSHIBA TC58NVM9S3ETA00 64MB on CS0 Found NAND on CS0: ACC=f7ff1010, cfg=14152300, flashId=98f00015, tim1=6574845b, tim2=00001e96 BrcmNAND version = 0x0400 64MB @00000000 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 page_shift=11, bbt_erase_shift=17, chip_shift=26, phys_erase_shift=17 brcmnand_scan 220 Brcm NAND controller version = 4.0 NAND flash size 64MB @1c000000 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=64, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=64, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 ECC layout=brcmnand_oob_bch4_4k brcmnand_scan: mtd->oobsize=64 brcmnand_scan: oobavail=50, eccsize=512, writesize=2048 brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a47990, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 not found for chip on CS0 Bad block table 1tbB not found for chip on CS0 File system address: 0xb93e0000 Scanning device for bad blocks, options=00004000 -->brcmnand_isbad_raw(offs=3fe0000 Bad block table written to 0x03fe0000, version 0x01 -->brcmnand_isbad_raw(offs=3fc0000 Bad block table written to 0x03fc0000, version 0x01 rescanning .... ----- Contents of BBT ----- ----- END Contents of BBT ----- brcmnandCET: Did not find CET, recreating brcmnandCET: Status -> Deferred brcmnand_scan 99 Root file system size 13a0000 Creating 4 MTD partitions on "brcmnand.0": 0x0000013e0000-0x0000025e0000 : "rootfs" 0x000002760000-0x000002b60000 : "data" 0x000000000000-0x000000020000 : "nvram" 0x000002b60000-0x000003f00000 : "fw" ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Watchdog Timer Init -- kthread brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x10 is enabled PCIe: No device found - Powering down Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmPktDma_init: Broadcom Packet DMA Library initialized bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.4 Jan 20 2017 09:49:26 p8021ag: p8021ag_init entry IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. Freeing unused kernel memory: 152k freed Empty flash at 0x000031e4 ends at 0x00003800 Empty flash at 0x00123504 ends at 0x00123800 Empty flash at 0x0012cb2c ends at 0x0012d000 Empty flash at 0x00131428 ends at 0x00131800 JFFS2 notice: (225) check_node_data: wrong data CRC in data node at 0x0000666c: read 0x965adb67, calculated 0x2c3d788a. JFFS2 notice: (225) check_node_data: wrong data CRC in data node at 0x000021a0: read 0x965adb67, calculated 0x7f308400. JFFS2 notice: (226) check_node_data: wrong data CRC in data node at 0x006f177c: read 0x61258b67, calculated 0xa38181d8. chipinfo: module license 'proprietary' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Jan 20 2017 09:48:05 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4730, buf size=2128 Broadcom BPM Module Char Driver v0.1 Jan 20 2017 09:47:59 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Jan 20 2017 09:48:06 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Jan 20 2017 09:48:06 chipId 0x631680D0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Jan 20 2017 09:48:00 Registered <241> Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa241cf90 0xa249cf90 Allocated FAP0 GSO Buffers (0xA242E018) : 1048576 bytes @ 0xA2500000 Allocated FAP1 GSO Buffers (0xA24AE018) : 1048576 bytes @ 0xA2600000 Allocated FAP0 TM SDRAM Queue Storage (a242e01c) : 341376 bytes @ a2700000 Allocated FAP1 TM SDRAM Queue Storage (a24ae01c) : 341376 bytes @ a2780000 [NTC fapProto] fapReset : Reset FAP Protocol layer fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3960>, free <2696>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3960>, free <2696>, total<8192> [FAP0] PSM : addr<0x80002000>, used <23436>, free <1140>, total <24576> [FAP1] PSM : addr<0x80002000>, used <23436>, free <1140>, total <24576> [FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP0] GSO Buffer set to 0xA2500000 [FAP1] GSO Buffer set to 0xA2600000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. [FAP0] FAP TM: ON [FAP1] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM63168D0 Ethernet Network Device v0.1 Jan 20 2017 09:49:21 fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb0820650 fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000 ETH Init: Ch:1 - 200 tx BDs at 0xb0a20650 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb0821910 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth2: MAC Address: 1C:74:0D:04:9F:30 eth1: MAC Address: 1C:74:0D:04:9F:30 eth0: MAC Address: 1C:74:0D:04:9F:30 eth3: MAC Address: 1C:74:0D:04:9F:30 eth4: MAC Address: 1C:74:0D:04:9F:30 eth0 Link UP 10 mbps full duplex eth4 Link UP 1000 mbps full duplex message received before monitor task is initialized kerSysSendtoMonitorTask Broadcom BCM3168D0 USB Network Device v0.4a Jan 20 2017 09:48:11 usb0: MAC Address: 1C 74 0D 04 9F 31 usb0: Host MAC Address: 1C 74 0D 04 9F 32 hub 1-0:1.0: over-current change on port 2 USBD Initialization done status 0 USB Link DOWN. message received before monitor task is initialized kerSysSendtoMonitorTask [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Jan 20 2017 09:47:58 Registered <245> --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3074 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=256 Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_map.bin srom rev:8 wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=32 wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L08.4 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered Broadcom 802.1Q VLAN Interface, v0.1 Host MIPS Clock divider pwrsaving is enabled DDR Self Refresh pwrsaving is enabled Energy Efficient Ethernet is disabled eth0 Link DOWN. message received before monitor task is initialized kerSysSendtoMonitorTask ip_tables: (C) 2000-2006 Netfilter Core Team eth0 Link UP 10 mbps full duplex message received before monitor task is initialized kerSysSendtoMonitorTask ip6_tables: (C) 2000-2006 Netfilter Core Team device eth0 entered promiscuous mode br0: port 1(eth0) entering forwarding state device eth2 entered promiscuous mode br0: port 1(eth0) entering disabled state br0: port 1(eth0) entering forwarding state ADDRCONF(NETDEV_UP): eth2: link is not ready device eth3 entered promiscuous mode br0: port 1(eth0) entering disabled state br0: port 1(eth0) entering forwarding state ADDRCONF(NETDEV_UP): eth3: link is not ready device eth1 entered promiscuous mode br0: port 1(eth0) entering disabled state br0: port 1(eth0) entering forwarding state ADDRCONF(NETDEV_UP): eth1: link is not ready device wl0 entered promiscuous mode br0: port 1(eth0) entering disabled state br0: port 1(eth0) entering forwarding state br0: port 5(wl0) entering forwarding state *** dslThread dslPid=1286 BcmAdsl_Initialize=0xC026FB70, g_pFnNotifyCallback=0xC02AC8F4 lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x1B7768 0xDEADBEEF *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xDACE8 => 0x111500 *** AdslCoreSharedMemInit: shareMemSize=133853(133856) AdslCoreHwReset: pLocSbSta=80d80000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3F9A5F4 ***BcmDiagsMgrRegisterClient: 0 *** dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22be0 bytes remaining 584 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22be0 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a23220 bytes remaining 456 XTM Init: Ch:1 - 16 rx BDs at 0xb0a23220 bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system Line 0: xDSL G.994 training message received before monitor task is initialized kerSysSendtoMonitorTask device eth4 entered promiscuous mode br0: port 6(eth4) entering forwarding state nf_conntrack version 0.5.0 (1024 buckets, 4096 max) monitor task is initialized pid= 295 br0: port 5(wl0) entering disabled state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state Line 0: VDSL G.993 started device wl0 entered promiscuous mode br0: port 6(eth4) entering disabled state br0: port 1(eth0) entering disabled state br0: port 6(eth4) entering forwarding state br0: port 1(eth0) entering forwarding state br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 6(eth4) entering disabled state br0: port 1(eth0) entering disabled state br0: port 6(eth4) entering forwarding state br0: port 1(eth0) entering forwarding state br0: port 5(wl0) entering forwarding state Line 0: VDSL2 link up, Bearer 0, us=3199, ds=31545 bcmxtmcfg: XTM Link Information, port = 0, State = UP, Service Support = PTM bcmxtmcfg: ReconfigureSAR port 0 traffictype 2 bcmxtmcfg: Normal(XTM/PTM) Mode enabled TxLineRateTimer=10003 bcmxtmrt: MAC address: 1c 74 0d 04 9f 34 [DoCreateDeviceReq.3137]: register_netdev [DoCreateDeviceReq.3139]: register_netdev done bcmxtmcfg: Reserve PTM vcid=0 ptmPri=1 port=0 bondingPort=4 bcmxtmcfg: Reserve PTM vcid=1 ptmPri=2 port=0 bondingPort=4 bcmxtmcfg: Reserve TxQueueIdx=0 for vcid 0 bcmxtmcfg: Reserve MP group=0 priority=0 weight=1 XTM Init: Ch:0 - 400 tx BDs at 0xa0810000 bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=3199000, DS=31545000 [FAP0] xtmCreateDevice : devId 0, encapType 0, headerLen 0 [FAP1] xtmCreateDevice : devId 0, encapType 0, headerLen 0 [FAP0] xtmLinkUp : devId 0, matchId 0 [FAP1] xtmLinkUp : devId 0, matchId 0 [FAP0] xtmLinkUp : devId 0, matchId 1 [FAP1] xtmLinkUp : devId 0, matchId 1 ptm0.1 MAC address set to 1C:74:0D:04:9F:35 netdev path : ptm0.1 -> ptm0 BCMVLAN : ptm0 mode was set to RG device ptm0 entered promiscuous mode netdev path : ppp1.1 -> ptm0.1 -> ptm0 Netfilter messages via NETLINK v0.30. bcmxtmcfg: Reserve TxQueueIdx=1 for vcid 0 XTM Init: Ch:1 - 400 tx BDs at 0xa0948000 bcmxtmcfg: Reserve TxQueueIdx=2 for vcid 0 XTM Init: Ch:2 - 400 tx BDs at 0xa096c000 bcmxtmcfg: Reserve TxQueueIdx=3 for vcid 0 XTM Init: Ch:3 - 400 tx BDs at 0xa080c000 usbserial: `0x' invalid for parameter `vendor' Intrusion -> IN=ppp1.1 OUT= MAC= SRC=191.101.167.235 DST=85.135.150.207 LEN=40 TOS=0x00 PREC=0x00 TTL=249 PROTO=TCP SPT=38685 DPT=8545 WINDOW=65535 RES=0x00 SYN URGP=0 MARK=0x8000000 Intrusion -> IN=ppp1.1 OUT= MAC= SRC=77.72.82.92 DST=85.135.150.207 LEN=40 TOS=0x00 PREC=0x00 TTL=249 PROTO=TCP SPT=58529 DPT=12393 WINDOW=1024 RES=0x00 SYN URGP=0 MARK=0x8000000 Intrusion -> IN=ppp1.1 OUT= MAC= SRC=77.72.82.80 DST=85.135.150.207 LEN=40 TOS=0x00 PREC=0x00 TTL=249 PROTO=TCP SPT=58011 DPT=8610 WINDOW=1024 RES=0x00 SYN URGP=0 MARK=0x8000000 Intrusion -> IN=ppp1.1 OUT= MAC= SRC=77.72.85.17 DST=85.135.150.207 LEN=40 TOS=0x00 PREC=0x00 TTL=250 PROTO=TCP SPT=47589 DPT=445 WINDOW=1024 RES=0x00 SYN URGP=0 MARK=0x8000000 ~ #
Buenisimooooo !!!!!!!